es posible que pongas la vitacora que arroja con el mensaje???

No se si la guarda en el mismo lugar que las distros basadas en red hat, pero prueba:

#tail -100 /var/log/messages

Click para expandir ...

nos cuentas que paso.

perdon por averme tardado pero mira cuando trato de correr una maquina me aparece esto:
Result Code:
NS_ERROR_FAILURE (0x80004005)
Component:
Machine
Interface:
IMachine {662c175e-a69d-40b8-a77a-1d719d0ab062}

luego me sale otro error:

Kernel driver not installed (rc=-1908)

The VirtualBox Linux kernel driver (vboxdrv) is either not loaded or there is a permission problem with /dev/vboxdrv. Please reinstall the kernel module by executing

'/etc/init.d/vboxdrv setup'

as root. Users of Ubuntu, Fedora or Mandriva should install the DKMS package first. This package keeps track of Linux kernel changes and recompiles the vboxdrv kernel module if necessary.

y poniendo lo que tu me dices sale esto:


Aug 23 22:18:03 bt kernel: [ 1.869612] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
Aug 23 22:18:03 bt kernel: [ 1.871344] EDD information not available.
Aug 23 22:18:03 bt kernel: [ 1.873169] Freeing unused kernel memory: 680k freed
Aug 23 22:18:03 bt kernel: [ 1.875228] Write protecting the kernel text: 5356k
Aug 23 22:18:03 bt kernel: [ 1.876997] Write protecting the kernel read-only data: 1884k
Aug 23 22:18:03 bt kernel: [ 1.898584] udev: starting version 151
Aug 23 22:18:03 bt kernel: [ 1.900424] udevd (70): /proc/70/oom_adj is deprecated, please use /proc/70/oom_score_adj instead.
Aug 23 22:18:03 bt kernel: [ 1.922149] forcedeth: Reverse Engineered nForce ethernet driver. Version 0.64.
Aug 23 22:18:03 bt kernel: [ 1.930206] ACPI: PCI Interrupt Link [APCH] enabled at IRQ 20
Aug 23 22:18:03 bt kernel: [ 1.933439] forcedeth 0000:00:07.0: PCI INT A -> Link[APCH] -> GSI 20 (level, low) -> IRQ 20
Aug 23 22:18:03 bt kernel: [ 1.939052] Floppy drive(s): fd0 is 1.44M
Aug 23 22:18:03 bt kernel: [ 1.943685] Linux agpgart interface v0.103
Aug 23 22:18:03 bt kernel: [ 1.959992] FDC 0 is a post-1991 82077
Aug 23 22:18:03 bt kernel: [ 1.963832] [drm] Initialized drm 1.1.0 20060810
Aug 23 22:18:03 bt kernel: [ 2.092021] usb 1-7: new high speed USB device using ehci_hcd and address 4
Aug 23 22:18:03 bt kernel: [ 2.460879] forcedeth 0000:00:07.0: ifname eth0, PHY OUI 0x732 @ 1, addr 00:24:1d:01:ec:97
Aug 23 22:18:03 bt kernel: [ 2.462779] forcedeth 0000:00:07.0: highdma pwrctl mgmt lnktim msi desc-v3
Aug 23 22:18:03 bt kernel: [ 2.464694] sata_nv 0000:00:08.0: PCI INT A -> Link[APSI] -> GSI 23 (level, low) -> IRQ 23
Aug 23 22:18:03 bt kernel: [ 2.466936] scsi0 : sata_nv
Aug 23 22:18:03 bt kernel: [ 2.468892] scsi1 : sata_nv
Aug 23 22:18:03 bt kernel: [ 2.470841] ata1: SATA max UDMA/133 cmd 0x9f0 ctl 0xbf0 bmdma 0xdc00 irq 23
Aug 23 22:18:03 bt kernel: [ 2.472703] ata2: SATA max UDMA/133 cmd 0x970 ctl 0xb70 bmdma 0xdc08 irq 23
Aug 23 22:18:03 bt kernel: [ 2.474951] scsi2 : pata_amd
Aug 23 22:18:03 bt kernel: [ 2.476845] scsi3 : pata_amd
Aug 23 22:18:03 bt kernel: [ 2.479026] ata3: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xf000 irq 14
Aug 23 22:18:03 bt kernel: [ 2.480859] ata4: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xf008 irq 15
Aug 23 22:18:03 bt kernel: [ 2.536021] usb 2-1: new low speed USB device using ohci_hcd and address 2
Aug 23 22:18:03 bt kernel: [ 2.944040] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
Aug 23 22:18:03 bt kernel: [ 2.952300] ata1.00: HPA detected: current 312579695, native 312581808
Aug 23 22:18:03 bt kernel: [ 2.954281] ata1.00: ATA-8: WDC WD1600AAJS-00B4A0, 01.03A01, max UDMA/133
Aug 23 22:18:03 bt kernel: [ 2.956289] ata1.00: 312579695 sectors, multi 16: LBA48 NCQ (depth 0/32)
Aug 23 22:18:03 bt kernel: [ 2.972278] ata1.00: configured for UDMA/133
Aug 23 22:18:03 bt kernel: [ 2.974447] scsi 0:0:0:0: Direct-Access ATA WDC WD1600AAJS-0 01.0 PQ: 0 ANSI: 5
Aug 23 22:18:03 bt kernel: [ 2.976749] sd 0:0:0:0: Attached scsi generic sg0 type 0
Aug 23 22:18:03 bt kernel: [ 2.976769] sd 0:0:0:0: [sda] 312579695 512-byte logical blocks: (160 GB/149 GiB)
Aug 23 22:18:03 bt kernel: [ 2.976804] sd 0:0:0:0: [sda] Write Protect is off
Aug 23 22:18:03 bt kernel: [ 2.976822] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 23 22:18:03 bt kernel: [ 2.994875] sda: sda1 < sda5 > sda2
Aug 23 22:18:03 bt kernel: [ 2.997387] sd 0:0:0:0: [sda] Attached SCSI disk
Aug 23 22:18:03 bt kernel: [ 3.056018] usb 2-2: new low speed USB device using ohci_hcd and address 3
Aug 23 22:18:03 bt kernel: [ 3.281226] input: PIXART USB OPTICAL MOUSE as /devices/pci0000:00/0000:00:02.0/usb2/2-1/2-1:1.0/input/input2
Aug 23 22:18:03 bt kernel: [ 3.283615] generic-usb 0003:093A:2510.0001: input,hidraw0: USB HID v1.11 Mouse [PIXART USB OPTICAL MOUSE] on usb-0000:00:02.0-1/input0
Aug 23 22:18:03 bt kernel: [ 3.308083] input: HID 04f3:0103 as /devices/pci0000:00/0000:00:02.0/usb2/2-2/2-2:1.0/input/input3
Aug 23 22:18:03 bt kernel: [ 3.310615] generic-usb 0003:04F3:0103.0002: input,hidraw1: USB HID v1.10 Keyboard [HID 04f3:0103] on usb-0000:00:02.0-2/input0
Aug 23 22:18:03 bt kernel: [ 3.326119] input: HID 04f3:0103 as /devices/pci0000:00/0000:00:02.0/usb2/2-2/2-2:1.1/input/input4
Aug 23 22:18:03 bt kernel: [ 3.328785] generic-usb 0003:04F3:0103.0003: input,hidraw2: USB HID v1.10 Device [HID 04f3:0103] on usb-0000:00:02.0-2/input1
Aug 23 22:18:03 bt kernel: [ 3.331454] usbcore: registered new interface driver usbhid
Aug 23 22:18:03 bt kernel: [ 3.334113] usbhid: USB HID core driver
Aug 23 22:18:03 bt kernel: [ 3.452043] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
Aug 23 22:18:03 bt kernel: [ 3.460343] ata2.00: HPA detected: current 1953523055, native 1953525168
Aug 23 22:18:03 bt kernel: [ 3.463043] ata2.00: ATA-8: ST31000528AS, CC46, max UDMA/133
Aug 23 22:18:03 bt kernel: [ 3.465735] ata2.00: 1953523055 sectors, multi 16: LBA48 NCQ (depth 0/32)
Aug 23 22:18:03 bt kernel: [ 3.484355] ata2.00: configured for UDMA/133
Aug 23 22:18:03 bt kernel: [ 3.487074] scsi 1:0:0:0: Direct-Access ATA ST31000528AS CC46 PQ: 0 ANSI: 5
Aug 23 22:18:03 bt kernel: [ 3.489894] sd 1:0:0:0: [sdb] 1953523055 512-byte logical blocks: (1.00 TB/931 GiB)
Aug 23 22:18:03 bt kernel: [ 3.489905] sd 1:0:0:0: Attached scsi generic sg1 type 0
Aug 23 22:18:03 bt kernel: [ 3.495225] sd 1:0:0:0: [sdb] Write Protect is off
Aug 23 22:18:03 bt kernel: [ 3.497852] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Aug 23 22:18:03 bt kernel: [ 3.521201] sdb: sdb1 sdb2
Aug 23 22:18:03 bt kernel: [ 3.524047] sd 1:0:0:0: [sdb] Attached SCSI disk
Aug 23 22:18:03 bt kernel: [ 10.005027] EXT4-fs (sda5): mounted filesystem with ordered data mode. Opts: (null)
Aug 23 22:18:03 bt kernel: [ 11.692869] EXT4-fs (sda5): re-mounted. Opts: errors=remount-ro
Aug 23 22:18:03 bt kernel: [ 11.825444] udev: starting version 151
Aug 23 22:18:03 bt kernel: [ 13.216350] parport_pc 00:0b: reported by Plug and Play ACPI
Aug 23 22:18:03 bt kernel: [ 13.216395] parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
Aug 23 22:18:03 bt kernel: [ 13.291256] ppdev: user-space parallel port driver
Aug 23 22:18:03 bt kernel: [ 13.291466] lp: driver loaded but no devices found
Aug 23 22:18:03 bt kernel: [ 13.312158] lp0: using parport0 (interrupt-driven).
Aug 23 22:18:03 bt kernel: [ 13.516059] i2c i2c-0: nForce2 SMBus adapter at 0x1c00
Aug 23 22:18:03 bt kernel: [ 13.516096] i2c i2c-1: nForce2 SMBus adapter at 0x1c40
Aug 23 22:18:03 bt kernel: [ 13.684924] cfg80211: Calling CRDA to update world regulatory domain
Aug 23 22:18:04 bt kernel: [ 14.484199] forcedeth 0000:00:07.0: eth0: no link during initialization
Aug 23 22:18:04 bt kernel: [ 14.484833] ADDRCONF(NETDEV_UP): eth0: link is not ready
Aug 23 22:18:04 bt kernel: [ 14.817595] ieee80211 phy0: hwaddr 00:18:e7:54:62:07, RTL8187BvE V0 + rtl8225z2, rfkill mask 2
Aug 23 22:18:04 bt kernel: [ 14.839080] rtl8187: Customer ID is 0x00
Aug 23 22:18:04 bt kernel: [ 14.839940] rtl8187: wireless switch is on
Aug 23 22:18:04 bt kernel: [ 14.839978] usbcore: registered new interface driver rtl8187
Aug 23 22:18:04 bt kernel: [ 14.914350] cfg80211: World regulatory domain updated:
Aug 23 22:18:04 bt kernel: [ 14.914352] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
Aug 23 22:18:04 bt kernel: [ 14.914355] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
Aug 23 22:18:04 bt kernel: [ 14.914358] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
Aug 23 22:18:04 bt kernel: [ 14.914360] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
Aug 23 22:18:04 bt kernel: [ 14.914363] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
Aug 23 22:18:04 bt kernel: [ 14.914366] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
Aug 23 22:18:04 bt kernel: [ 15.226849] ACPI: PCI Interrupt Link [AAZA] enabled at IRQ 23
Aug 23 22:18:04 bt kernel: [ 15.226857] HDA Intel 0000:00:05.0: PCI INT B -> Link[AAZA] -> GSI 23 (level, low) -> IRQ 23
Aug 23 22:18:04 bt kernel: [ 15.226861] hda_intel: Disable MSI for Nvidia chipset
Aug 23 22:18:05 bt kernel: [ 15.952093] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:05.0/input/input5
Aug 23 22:18:06 bt kernel: [ 16.824457] nvidia: module license 'NVIDIA' taints kernel.
Aug 23 22:18:06 bt kernel: [ 16.824462] Disabling lock debugging due to kernel taint
Aug 23 22:18:06 bt kernel: [ 17.347031] ACPI: PCI Interrupt Link [APC8] enabled at IRQ 16
Aug 23 22:18:06 bt kernel: [ 17.347050] nvidia 0000:02:00.0: PCI INT A -> Link[APC8] -> GSI 16 (level, low) -> IRQ 16
Aug 23 22:18:06 bt kernel: [ 17.347069] vgaarb: device changed decodes: PCI:0000:02:00.0,olddecodes=io+mem,decodes=nonewns=io+mem
Aug 23 22:18:06 bt kernel: [ 17.347234] NVRM: loading NVIDIA UNIX x86 Kernel Module 275.09.07 Wed Jun 8 15:42:20 PDT 2011
Aug 23 22:18:08 bt kernel: [ 19.162579] ADDRCONF(NETDEV_UP): wlan0: link is not ready
Aug 23 22:19:04 bt kernel: [ 75.126485] ADDRCONF(NETDEV_UP): wlan0: link is not ready
Aug 23 22:19:04 bt kernel: [ 75.252386] forcedeth 0000:00:07.0: eth0: no link during initialization
Aug 23 22:19:04 bt kernel: [ 75.253006] ADDRCONF(NETDEV_UP): eth0: link is not ready
Aug 23 22:19:08 bt kernel: [ 79.210459] ADDRCONF(NETDEV_UP): wlan0: link is not ready
Aug 23 22:19:13 bt kernel: [ 84.053084] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready

es mucho pero puesaqui esta toda la info eso creo espero puedan ayudarme gracias

y si corro este comando /etc/init.d/vboxdrv setup sale :


* Stopping VirtualBox kernel modules [ OK ]
* Uninstalling old VirtualBox DKMS kernel modules [ OK ]
* Trying to register the VirtualBox kernel modules using DKMS
Error! Your kernel headers for kernel 2.6.38 cannot be found at
/lib/modules/2.6.38/build or /lib/modules/2.6.38/source.

* Failed, trying without DKMS
* Recompiling VirtualBox kernel modules
* Look at /var/log/vbox-install.log to find out what went wrong

y ya intentaste hacer lo que te dice le mensaje, instalar los kernel headers ¿?

mmm que mensaje dice eso ajajajaj

pues segunyo los instale use :

apt-get install linux-headers-`uname -r`

amenosque no ayan sido esos :/

me aparece esto:


Reading package lists... Done
Building dependency tree
Reading state information... Done
linux-headers-2.6.38 is already the newest version.

ese que dice ¿?

para hacer esto:
debes instalar los paquetes de desarrollo [devel en ubuntu no recuerdo que nombre tienen] del kernel.

o seguir las intrucciones de aca:

creo que esa version de backtrack esta basada de ubuntu, no ¿?

ya he hecho todo ya tengo el dkms y todo pero no me funciona :/

Nimbue dijo:

ya he hecho todo ya tengo el dkms y todo pero no me funciona :/

Click para expandir ...

ok...

que es lo que contiene esto ¿?

Uninstalling modules from DKMS
removing old DKMS module vboxhost version 4.1.2

------------------------------
Deleting module version: 4.1.2
completely from the DKMS tree.
------------------------------
Done.
Attempting to install using DKMS

Creating symlink /var/lib/dkms/vboxhost/3.2.12/source ->
/usr/src/vboxhost-3.2.12

DKMS: add Completed.
You can use the --kernelsourcedir option to tell DKMS where it's located, or you could install the linux-headers-2.6.38 package.
Failed to install using DKMS, attempting to install without
Makefile:159: *** Error: unable to find the sources of your current Linux kernel. Specify KERN_DIR=<directory> and run Make again. Stop.

pues hay te indica que te falta linux-headers, si los tienes instalados ¿?
búscalos en synaptic marcalos e instalalos.
y también instala build-essential [en synaptic marcas e instalas]
y despues va de nuevo.

ya si con eso no funciona, no se me ocurre otra cosa.

es básicamente lo que dice aca:
http://ubuntuforums.org/archive/index.php/t-853374.html

y algo mas.

cuando usaste este comando, lo usaste como tal?
o primero uname -r y con el resultado:
¿?

nadamas puse el apt-get install linux-headers-`uname -r` tal y como esta

Nimbue dijo:

nadamas puse el apt-get install linux-headers-`uname -r` tal y como esta

Click para expandir ...

hijoles...

la manera mas fácil es que abras synaptic y busques linux-headers, marques e instales, tal vez te salgan varios, solo instala la versión que corresponde a tu kernel, para eso es el comando uname -r [por eso en comillas en el comando anterior], tampoco mencionas si ya instalaste el build-essential y trataste de nuevo.

por ejemplo;
después en mi caso, si usara alguna debian-based en synaptic buscaría el linux-headers-2.6.37.6-0.7-desktop
o con:

juas jajaja mmm bueno jaja este ya empine el bt5 jajaa trate de hacer un dual boot con megia y lo trone todo jajajaja dejen reinstalo todo de nuevo y les digo jajaja

Mageia excelente distro, usa grub, solo era reparar el grub 2 de backtrack (yo supongo)

jajaaj pues si mageia es muy bueno lo maneje vario tiempo, solo que no se si recuerdas que te mande por privado que las x no arrancaba, bueno ya me paso loreinstale como 6 veces y nunca funciono asi quecreo que probare otra distro, pardus dama dama seraaaa

despues de moverle mucho y mucho ya hice que cambiara el log de errores ahora me aparece :

Makefile:172: *** Error: unable to find the sources of your current Linux kernel. Specify KERN_DIR=<directory> and run Make again. Stop.


aki si ya no se ke hacer alguien que me pueda asesorar plz

jus ya pude instalarlo lo que hice fue irme al directorio: /usr/src/ aqui fue copiar la carpeta con los headers luego pasarme al directorio: /lib/modules/2.x.xx/ pegar aqui la carpeta de linux-headers-2.xx.xx ( que copiamos con anterioridad), cambiarle el nombre a build y despues correr el comando: /etc/init.d/vboxdrv setup y se recompila y ya funciona el vbox por si les interesa asi mefunciono a mi gracias a todos